Brak autoformerów wpływa pozytywnie na zrównoważenie brzmienia. Potężny zasilacz oparty na drogim transformatorze wykonanym na rdzeniu EI pozwala w pełni kontrolować trudne kolumny oraz bez problemów radzi sobie ze skomplikowanymi nagraniami o gęstej fakturze.
Szczegółowe opisy brzmienia znajdziesz na stronach :
http://www.audiostereo.pl/McIntosh6500_grzechu_warty_10649.html
http://www.audioreview.com/mfr/mcintosh/amplifiers/ma6500/PRD_124533_1583crx.aspx
Uwagi:
Stan idealny, komplet z oryginalnym kartonem, instrukcją oraz dowodem zakupu w Polsce. FREQUENCY RESPONSE: 20Hz to 20kHz, +0 / -0.5dB TOTAL HARMONIC DISTORTION 0.005% max. at any level from 250 milliwatts to rated power output per channel from 20Hz to 20kHz. INTERMODULATION DISTORTION SMPTE 0.005% maximum if instantaneous peak output does not exceed 400W per channel POWER OUTPUT 200, 120 watts minimum sine wave continuous average power output per channel, both channels operating, into a load impedance of 4, and 8 ohms respectively. A-WEIGHTED SIGNAL-TO-NOISE RATIO Power amp: 110dB below rated output High level: 100dB below rated output (90dB IHF) Phono: 90dB below 10 mV input (84dB IHF) INPUT IMPEDANCE: High level: 22k ohms Phono: 47k ohms, 65pf Main in: 20k ohms OUTPUT LOAD IMPEDANCE: 4 or 8 ohms INPUT SENSITIVITY High level: 250mV for 2.5V rated output (50mV IHF) Phono: 2.5mV for 2.5V rated output (o.5mV IHF) Main in: 2.5V for rated output DAMPING FACTOR :230 (8 ohms), 120 (4 ohms) RATED POWER BAND: 20Hz to 20kHz DYNAMIC HEADROOM: 2.4dB MAXIMUM PREAMP VOLTAGE OUTPUT: 8V from 20Hz to 20kHz MAXIMUM INPUT SIGNAL: High level: 8V; Phono: 90mV VOLTAGE GAIN : High level to tape: 0dB; High level to main: 20dB TONE CONTROLS: Bass and treble: + 12dB POWER GUARD: Clipping is prevented and THD does not exceed 2% with up to14dB overdrive at 1kHz POWER REQUIREMENTS: 120V 50/60Hz, 4A DIMENSIONS (H X W X D): inch: 71â�„16" x 171â�„2" x 181â�„8" cm: 17.9 x 44.5 x 46 includes clearance for connectors knob clearance: 11â�„8" (2.9 cm) FREQUENCY RESPONSE 20Hz to 20kHz, +0 / -0.5dB TOTAL HARMONIC DISTORTION 0.005% max. at any level from 250 milliwatts to rated power output per channel from 20Hz to 20kHz. INTERMODULATION DISTORTION SMPTE 0.005% maximum if instantaneous peak output does not exceed 400W per channel POWER OUTPUT 200, 120 watts minimum sine wave continuous average power output per channel, both channels operating, into a load impedance of 4, and 8 ohms respectively. A-WEIGHTED SIGNAL-TO-NOISE RATIO Power amp: 110dB below rated output High level: 100dB below rated output (90dB IHF) Phono: 90dB below 10 mV input (84dB IHF) INPUT IMPEDANCE High level: 22k ohms Phono: 47k ohms, 65pf Main in: 20k ohms OUTPUT LOAD IMPEDANCE: 4 or 8 ohms INPUT SENSITIVITY High level: 250mV for 2.5V rated output (50mV IHF) Phono: 2.5mV for 2.5V rated output (o.5mV IHF) Main in: 2.5V for rated output DAMPING FACTOR :230 (8 ohms), 120 (4 ohms) RATED POWER BAND: 20Hz to 20kHz DYNAMIC HEADROOM: 2.4dB MAXIMUM PREAMP VOLTAGE OUTPUT: 8V from 20Hz to 20kHz MAXIMUM INPUT SIGNAL: High level: 8V; Phono: 90mV VOLTAGE GAIN : High level to tape: 0dB; High level to main: 20dB TONE CONTROLS: Bass and treble: + 12dB POWER GUARD: Clipping is prevented and THD does not exceed 2% with up to14dB overdrive at 1kHz POWER REQUIREMENTS: 120V 50/60Hz, 4A DIMENSIONS (H X W X D): inch: 71â�„16" x 171â�„2" x 181â�„8" cm: 17.9 x 44.5 x 46 includes clearance for connectors knob clearance: 11â�„8" (2.9 cm) WEIGHT: 74.5 pounds (33.8 Kg) net, 92.5 pounds (41.7 Kg) in shipping carton
